Lakeshore 330 Скачать руководство пользователя страница 74

Страница: 74 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

5-6

Service & Calibration

5.8 ERROR

MESSAGES

On power up, the Model 330 checks internal memory. There are two potential error messages.

The first error,

Er01

, indicates an unsuccessful attempt to write and then read the internal non-volatile RAM. This error is not

user-correctable. Consult the factory.

The second error,

Er02

, indicates an unsuccessful attempt to read the internal non-volatile RAM for the Model

ID. Sometimes, initializing memory corrects this error. To initialize memory, press and hold both

Escape

and

Units

for about 20 seconds. Release when the power up sequence begins. Perform this operation only under

extreme circumstances; it erases any user-defined curves in memory.

There are two sensor input error messages. If an input signal from the sensor exceeding full scale is applied

to the input leads,

indicates the overload.

If no signal or a wrong polarity signal exists at the input leads,

Er27

indicates a Zero Error for Channel A or

Er28

for Channel B. The Model 330 displays dashes “

- - -

” if the

input switches are improperly set.

Finally,

Er30

appears if the measured heater output does not match the predicted output. The controller turns

the heater off. Check heater resistance, test for shorts in the heater wiring, then turn the heater on again. If the

error message returns, consult the factory.

Table 5-1. Sensor Input Setup

Sensor

DIP Switch

Settings

Display When

Input Type

Key is Pressed

Sensor

Units

Input

Range

Standard

Curve(s)

Silicon Diode

(DT-400

Series)

Volts

0 to 2.5

2 Curve10
4 Curve 10 SoftCal

Thermocouple

(compensation

on)

Millivolts

15 to 15

Platinum

RTD

Ohms

0 to 300

3 DIN Curve 43760

GaAlAs

Diode

Volts

0 to 6.0

None

10 to 10

6 AuFe 0.07% vs. Chromel

7 AuFe 0.03% vs. Chromel

8 Type E (chromel-constantan)

9 Type K (chromel-alumel)

10 Type T (copper-constantan)

Thermocouple

(compensation

off)

Millivolts

DIP Switch S1 is for Channel A and S2 is for Channel B.

If the internal DIP switches are improperly set, the
display will read Er when the

Input Type

key is

pressed. The normal front panel display will show
dashes - - - - to indicate improper DIP switch setting.

Improper Switch Setting

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 74 / 104

Результаты поиска

Содержание 330

Отзывы: