Lakeshore 330 Скачать руководство пользователя страница 28

Страница: 28 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

3-2

Operation

Set Point:

Displays or adjusts the control loop temperature setpoint (Paragraph 3.3.2). Press and hold this

key to access the ramp rate feature, where the user sets the rate at which the temperature setpoint

automatically increases or decreases when the user changes the setpoint value. See Paragraph 3.3.3.

Control:

Returns bottom display to Control sensor readouts after reading or adjusting the setpoint. See

Paragraph 3.3.2.

Escape:

Terminate a function without changing existing settings. To reset most controller parameters to

factory defaults, press and hold both the

Escape

and

Units

keys for about 20 seconds. See Paragraph 3.4.4.

Used in conjunction with other keys to increment or toggle readings in the upper Sample window.

Used in conjunction with other keys to increment or toggle readings in the lower Control window.

Enter:

Accepts changes made in the field display. Press and hold the

Enter

key to access the Power Up

(PUP) configuration setup display. See Paragraph 3.4.5.

Local:

Switches controller between Local (LOC) and Remote (REM) operation. See Paragraph 3.4.3.

SoftCal:

Improves silicon diode sensor accuracy by setting up a special modification to the Standard Curve

10. See Paragraph 3.2.7.

Autotune:

Sets controller tuning to P, PI, PID, Zone, or Off. See Paragraph 3.3.4.

and

This symbol next to a key indicates the function operates by holding the key and pressing the

key

to change the top display setting, and the

key to change the bottom display setting.

3.1.2

Front Panel LED Display

In normal operation, the front panel LED display shows Sample/Control temperature readings and heater

status. Other information displays on the various displays to the left and right of the temperature readings. See

Figure 3-2.

Sample

REM

OFF

Control

LOC
TUNE
CAL

HIGH
MED
LOW

K
C
ž
V

A
B

K
C
ž
V

A
B

Remote/Local

P, PI, PID, or

Zone Tuning

Heater Range

Units

Channel

Setpoint

SoftCal™

C-330-U-3-2

Figure 3-2. Definition of Front Panel LED Display

3.2 THERMOMETRY

FUNCTIONS

The following front panel keyboard functions relate to Model 330 thermometry:

Input Type (Paragraph 3.2.1),

Channel (Paragraph 3.2.2), Units (Paragraph 3.2.3), Temperature Compensation (Paragraph 3.2.4), Display

Filter (Paragraph 3.2.5), Curve (Paragraph 3.2.6), and SoftCal (Paragraph 3.2.7).

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 28 / 104

Результаты поиска

Содержание 330

Отзывы: