Lakeshore 330 Скачать руководство пользователя страница 71

Страница: 71 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

Service & Calibration

5-3

5.4

IEEE-488 INTERFACE CONNECTOR

Connect to the IEEE-488 Interface connector on the Model 330 rear with cables specified in the IEEE-488-

1978 standard document. The cable has 24 conductors with an outer shield. The connectors are 24-way

Amphenol 57 Series (or equivalent) with piggyback receptacles to allow daisy-chaining in multiple device

systems. The connectors are secured in the receptacles by two captive locking screws with metric threads.

The total length of cable allowed in a system is 2 meters for each device on the bus, or 20 meters maximum.

A system may be composed of up to 15 devices. Figure 5-5 shows the IEEE-488 Interface connector pin

location and signal names as viewed from the Model 330 rear panel.

IEEE-488 INTERFACE

SH1 AH1 T5 L4 SR1 RL1 PP0 DC1 DT0 C0 E1

PIN SYMBOL

DESCRIPTION

DIO1

DIO2

DIO3

DIO4

EOI

DAV

NRFD

NDAC

IFC

SRQ

ATN

SHIELD

DIO5

DIO6

DIO7

DIO8

REN

GND 6

GND 7

GND 8

GND 9

GND 10

GND11

GND

Data Input/Output Line 1

Data Input/Output Line 2

Data Input/Output Line 3

Data Input/Output Line 4

End Or Identify

Data Valid

Not Ready For Data

Not Data Accepted

Interface Clear

Service Request

Attention

Cable Shield

Data Input/Output Line 5

Data Input/Output Line 6

Data Input/Output Line 7

Data Input/Output Line 8

Remote Enable

Ground Wire – Twisted pair with DAV

Ground Wire – Twisted pair with NRFD

Ground Wire – Twisted pair with NDAC

Ground Wire – Twisted pair with IFC

Ground Wire – Twisted pair with SRQ

Ground Wire – Twisted pair with ATN

Logic Ground

Figure 5-5. IEEE-488 Rear Panel Connector Details

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 71 / 104

Результаты поиска

Содержание 330

Отзывы: