English
22 EN
Messages in explicit mode
15. Anomalies
Customer interventions
Before calling the servicing department, verify whether the problem encountered with the machine is described herebe-
low in order to avoid unnecessary expenses:
Softener
This message is displayed when the softener resins need
to be regenerated. (Follow the instructions on softener
maintenance).
Once regeneration has been completed,
keep the RESET key pressed for
ap-
proximately 8
seconds to cancel out the
message.
Machine in
stand-by
This message is displayed when the machine switch ON/
OFF has been programmed. The message indicates that
the machine is switch-off and is in stand-by status.
Refer to the Technician’s Manual to see
how to program the switch ON/OFF of
the machine.
Press the "
OK
" key for a few seconds to
force the machine on.
Blocked
keypad
During normal use of the machine, sometimes a key may
become mechanically blocked. If this happens and the key
remains blocked for more than 1 minute, this message will
appear on the display screen: BLOCKED KEY.
Note: All other keys except the one involved will function
normally.
To solve the problem, examine the keypad,
identify the blocked key that caused the
message, and follow the steps needed to
remedy the situation.
Messages
about
washings
Please consult this manual at the "Clean-
ing operations ".
ANOMALIES
CAUSE
REMEDY
The coffee machine does not func-
tion and the display (
5
) is off.
No electricity.
Check that the electricity is on.
Check the position of the main
switch (
23
).
Water leak in the cup-warmer tray (
16
) Clogged basin hole.
Clean
Coffee dispensing time too short.
Coffee ground too coarse.
Coffee too old.
8VHD¿QHUJULQG
Use new coffee.
Coffee drips out of machine.
&RIIHHJURXQGWRR¿QH
Use a coarser grind.
Loss of water under the machine.
Discharge well clogged up.
Clogged drainage basin
Clean.
Machine heated up, but it does not
dispense coffee.
Water supply or water softener tap
closed.
No water in system.
Open.
Wait until water is available or call a
plumber.
The automatic level control devices
remain in operation.
Same causes as above.
Same solution as above.
02_S39 TE_MULTI.indd 22
07/11/2017 17:00:24
Содержание S39 TE
