vii
REGIUS MODEL 190 Service Manual Ver.1.00 2004.11.01
C a u t i o n s r e l a t i n g t o L a w s
Following cautions must be observed when handling the REGIUS MODEL 190 and become thoroughly famil-
iar with the correct method of usage.
Cautions relating to Laser
Regulations
Be certain to comply with any and all laws and government regulations including electric codes
and utility regulations, regarding the installation and operation of this equipment.
Precautions to be observed when using medical electrical equipment (to
ensure safety and prevent danger)
1. Ensure that only a trained or approved operator uses the equipment.
2. When installing the equipment, observe the following precautions.
(1) Install the equipment in a location where it is not exposed to water.
(2) Install the equipment in a location where there is no likelihood of being
adversely affected by atmospheric pressure, temperature, humidity,
drafts, light, dust, or air containing salt, or sulfur, etc.
(3) Install the equipment in a stable location. Do not install it on an inclined
surface and avoid vibrational shock (including during transportation).
(4) Do not install the equipment in a location where chemical reagents are
stored or where chemical fumes may be present.
(5) Check the frequency, voltage and allowable current (or power consump-
tion) of the power source.
(6) Confirm the conditions of the batteries (how exposed they are, or their
polarity).
(7) Ground the equipment well.
3. Before using the equipment, observe the following precautions.
(1) Check the contact state of the switches, the polarity dial setting, and the
various meters, and confirm that the equipment operates normally.
(2) Make sure that the equipment is well grounded.
(3) Make sure that all the cables are connected correctly and safely.
(4) Using two X-ray devices at the same time may result in an incorrect diag-
nosis or hazards to people.
So, extreme care should be taken.
(5) Check the batteries.
<IMPORTANT>Should this manual become not readable due to any reason, replace it with a new one which
is available at charged basis.
The reader device uses a laser light and high voltage.
Never remove the external panel.
If you remove the external panel, you may be exposed to laser
light or receive an electric shock.
Specifications of laser unit on the REGIUS MODEL 190 are:
Class: IIIb*
Medium: Semiconductor laser
Wavelength: 660 nm
Maximum output: 80 mW (CW)
WARNING
Содержание REGIUS 190
