Komatsu HB365LC-3 Скачать руководство пользователя страница 286 | Manualshive

Страница: 286 / 506

background image

REMARK

The machine with the auto-greasing system require one time
lubrication each time the bucket is changed.
Lubricate at the bucket linkage and at the grease metering
valve as indicated until grease comes out from the end faces.
It will be necessary to replace the plug at the grease metering
valve with a grease nipple during lubrication. The plug must be
replaced after lubrication.

Grease metering valve for the standard machine

METHOD FOR PARKING MACHINE

k

k

WARNING

• Stop the machine gradually. Avoid a sudden stop.
• Place the machine on a firm and level place.

Do not park the machine on a slope.
Block the tracks from movement if it is unavoidably
necessary to park the machine on a slope. As an addi-
tional safety measure, thrust the work equipment into
the ground.

• The machine may move suddenly if the control lever is

touched  by  accident.  This  may  lead  to  a  serious  per-
sonal  injury  or  death.  Set  the  lock  lever  securely  to
LOCK  position  always  before  leaving  the  operator's
seat.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-214

«
...
284
285
286
287
288
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: Hitachi Страницы: 278

Бренд: Skandia Elevator Страницы: 28

Бренд: Woods Страницы: 60

Бренд: Kobelco Страницы: 20

Бренд: Kobelco Страницы: 79

Бренд: Kobelco Страницы: 96

Бренд: Kobelco Страницы: 135

Dynamic Acera SK450-VI

Бренд: Kobelco Страницы: 138

Бренд: Kobelco Страницы: 162

Бренд: Kobelco Страницы: 296

Бренд: Kobelco Страницы: 308

Бренд: Kobelco Страницы: 311

Бренд: Kobelco Страницы: 412

Бренд: Forum Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды