manualshive.com logo in svg

Komatsu HB365LC-3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu HB365LC-3 Скачать руководство пользователя страница 393

1.

Turn the starting switch to ON position (B).

2.

Keep pressing the test button (9) for 3 to 5 seconds.
The  system  performs  the  one  cycle  test.  The  green  LED
(4) of the selected lubrication interval on the display inside
the cab (2) flashes (lit 2 seconds, not lit 2 seconds) while
this test is being proceeded.
In order to provide additional grease to all grease points (i.
e. after cleaning the machine) or to vent the system, a con-
tinuous lubrication cycle run can be performed.

Procedure for continuous lubrication test
Perform the continuous lubrication test in order to check the system.
1.

Turn the starting switch to ON position (B).

MAINTENANCE

MAINTENANCE PROCEDURE

4-45

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды