manualshive.com logo in svg

Komatsu HB365LC-3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu HB365LC-3 Скачать руководство пользователя страница 341

1.

Connect the clip of jumper cable (A) to the positive (+) ter-
minal of battery (C) on the failed machine.

2.

Connect the clip at the other end of jumper cable (A) to the
positive (+) terminal of battery (D) on the normal machine.

3.

Connect the clip of jumper cable (B) to the negative (-) ter-
minal of battery (D) on the normal machine.

4.

Turn  the  battery  disconnect  switch  (S)  of  the  failed  ma-
chine to ON position.

5.

Connect the other clip of jumper cable (B) to the revolving
frame (E) of the failed machine.

METHOD FOR STARTING ENGINE

1.

Check both of normal machine and failed machine that the lock lever is set to LOCK position.
Check also that all the control levers are in NEUTRAL position.

2.

Make sure the clips are firmly connected to the battery terminals.

3.

Start the engine of the normal machine and run it at high idle (max. speed).

4.

Turn the starting switch of the failed machine to START position and start the engine.
If the engine does not start, try again after at least 2 minutes.

PROCEDURE FOR REMOVING JUMPER CABLE

After the engine has started, disconnect the jumper cables in the reverse of the order in which they were con-
nected.
1.

Remove  the  clip  of  jumper  cable  (B)  from  the  revolving
frame (E) of the failed machine.

2.

Remove the clip of jumper cable (B) from the negative (-)
terminal of battery (D) on the normal machine.

3.

Remove the clip of jumper cable (A) from the positive (+)
terminal of battery (D) on the normal machine.

4.

Remove the clip of jumper cable (A) from the positive (+)
terminal of battery (C) on the failed machine.

IF TROUBLES ON HYBRID SYSTEM OCCUR

• The problems of the hybrid system are shown in the following table.
• Contact your Komatsu distributor for the remedies indicated with ( ) in the remedy column.
• Ask your Komatsu distributor for repairs for problems or causes which are not listed below.

Problem

Main causes

Remedy

Does not swing.

PPC lock lever is still applied.

Pull up the PPC lock lever.

Swing lock switch is still applied

Turn off the swing lock switch.

Hybrid system stop switch is still ap-
plied.

Turn off the hybrid system stop
switch.

Defective swing PPC pressure sen-
sor

(Replace the sensor.)

Engine power deration due to lower-
ing of DEF level

Add the DEF.

Engine power deration due to abnor-
mality in urea SCR system device

(Check and repair.) (Replace the de-
vice.)

OPERATION

TROUBLES AND ACTIONS

3-269

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды