Komatsu HB365LC-3 Скачать руководство пользователя страница 427 | Manualshive

Страница: 427 / 506

Komatsu HB365LC-3 Скачать руководство пользователя страница 427

There may be oil accumulated or sticking in the case and
element. Take care not to spill the oil when replacing the
element.

REMARK

When the ambient temperature is low, water or emulsified
matter may stick to the inside of KCCV because of con-
densation of water vapor in the blowby gas. However, if
the coolant level is normal, it is not a problem.

3.

Remove the used O-ring (6) sticking to the case (4) and install a new O-ring contained in the service kit.
Apply the engine oil to the new O-ring.

4.

While matching the

◇

marks (7) of the new element with

the

◇

mark (8) of the body label, insert the element firmly

into the end of the body.

The element can be installed only when its claws (9) are
correctly inserted in grooves (10) of the filter body. Bases
(11) and (12) are oval. When inserting, take extreme care
so that those bases are matched with each other.

5.

Align the position of

◇

mark (13) on the case with that of

◇

mark (8) of the filter body label, then install the case to the
filter body.

MAINTENANCE

MAINTENANCE PROCEDURE

4-79

«
...
425
426
427
428
429
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды