Komatsu HB365LC-3 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 506

Komatsu HB365LC-3 Скачать руководство пользователя страница 121

TRAVEL SPEED SELECTOR SWITCH

k

k

WARNING

• When loading to or unloading from a trailer, always drive the machine at low speed (set the travel

speed selector switch to Lo) and never operate the travel speed selector switch during travel.

• If the travel speed is switched between Hi and Lo when the machine is traveling, the machine may

deviate to one side, even when traveling in a straight line. Stop the machine before switching the
travel speed.

Travel speed selector switch is used to select the travel speed
from 3 stages.
Lo lights up: Low-speed travel
Mi lights up: Mid-range speed travel
Hi lights up: High-speed travel
When  the  engine  is  started,  the  speed  is  automatically  set  to
Lo.
Each time that the switch is pressed, the display changes Lo →
Mi → Hi → Lo in turn.
Even if the travel speed is set to high-speed (Hi) or a mid-range
speed (Mi), when traveling on soft ground or uphill, and travel
power is needed, the system automatically shifts down to low-
speed  travel  (Lo).  There  is  no  need  to  operate  the  switch.  In
this  case,  the  travel  speed  on  the  machine  monitor  display
stays lit at Hi (high-speed) or Mi (mid-range speed).

REMARK

Each time the travel speed selector switch is switched, the
mode is displayed on the machine monitor display, and after 2
seconds, the screen returns to the standard screen.

OPERATION

EXPLANATION OF COMPONENTS

3-49

«
...
119
120
121
122
123
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды