Komatsu HB365LC-3 Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 506

background image

Install the mirror (1) to support (3), then tighten it with mounting
bolt (2).

METHOD FOR REMOVING AND INSTALLING HANDRAIL

k

k

WARNING

• After the machine is transported, be sure to install the handrails before inspection and mainte-

nance.

• Use the crane, etc. for carrying the handrails.

There is a danger of rolling over or falling from high place that can lead to serious personal injury or
death. Check the scaffolding and ensure your safety before starting the work.

• If installation or removal work of the handrail is improper, there is a hazard that someone may fall

from the machine during the installation or removal work.
Follow the procedure below during the installation or removal work.

METHOD FOR REMOVING HANDRAIL

Remove the handrails in the order (A), (B), and (C).

1.

Remove the bolts (1), and remove the handrail (A) and
cover (2).

OPERATION

TRANSPORTATION

3-249

«
...
319
320
321
322
323
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: Yuchai Страницы: 131

Бренд: Doosan Страницы: 136

Бренд: Agrison Страницы: 83

Бренд: P.Lindberg Страницы: 97

Бренд: Kato Imer Страницы: 120

Бренд: Land Pride Страницы: 38

Бренд: RANKO Страницы: 61

Бренд: Wacker Neuson Страницы: 228

Бренд: Wacker Neuson Страницы: 248

Бренд: Wacker Neuson Страницы: 29

AP Cumberland PNEG-650-1

Бренд: GSI Group Страницы: 10

Бренд: Bush Hog Страницы: 1

Бренд: NPK Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды