manualshive.com logo in svg

Komatsu HB365LC-3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu HB365LC-3 Скачать руководство пользователя страница 207

“SCR Information” screen message (4): “4 Engine power is
under heavy deration.”
Due to the further deration of engine power, capability the
machine will be limited further.
Hybrid system power is also under deration. This results in
low swing motor power.
“Severe Inducement” is the final status of Inducement.
Unless  all  the  “SCR  system”  abnormalities  are  corrected,
engine performance will be kept derated.

Engine power can be restored temporarily from power derate. If Inducement advances to “Severe Induce-
ment”  and  it  becomes  necessary  to  restore  engine  power,  use  the  engine  power  restoration  function  to
move  the  machine  to  a  safe  place  and  contact  your  Komatsu  distributor.  This  engine  power  restoration
works only when the Inducement status is “Severe Inducement” and relieves back temporarily to the power
deration of “Low level Inducement”. The operator can restore engine power through the machine monitor.
For  the  engine  power  restoration  procedure,  refer  to  the  section  of  “Temporary  Restoration  from  Induce-
ment” in this manual.

Inducement  strategy  when  abnormality  is  found  in  the  KDPF  System  by  the
Urea SCR system

If any abnormality is detected in the KDPF System through the Urea SCR system, the Inducement strategy is
activated.
The  inducement  strategy  progresses  in  4  levels,  “Warning”,
“Continuous Warning”, “Low level Inducement”, and “Severe In-
ducement”.  The  Inducement  strategy  includes  visual  alert  by
the KDPF System caution lamp (1), DEF system caution lamp
(2), and Action Level displayed on the machine monitor (3), au-
dible alert by a buzzer and stepwise engine power deration that
advances to speed limitation to low idle. Engine power deration
starts  with  Action  Level  “L03  (Warning,  Continuous  Warning
and  Low  level  Inducement)”  and  advances  to  further  deration
when  “L04  (Severe  Inducement)”  is  displayed.  Once  the  sys-
tem  advances  to  “Severe  Inducement”,  the  engine  power  will
be further derated. If “L03” is displayed, move the machine to a
safe place and contact your Komatsu distributor.
The content of the warning can be checked on the “SCR Information” screen of the user menu.
Perform the following procedure.
Press F6 on the standard screen to display the “SCR Informa-
tion” screen of the user menu.

OPERATION

EXPLANATION OF COMPONENTS

3-135

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды