Komatsu HB365LC-3 Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 506

background image

METHOD FOR ADJUSTING SEAT UNIT IN FORE-AND-AFT DIRECTION

Pull the fore-aft adjustment lever (8) to the right, set the seat to the desired position, then release the lever.
The operator's seat, right and left control levers, and lock lever move together.
Fore-and-aft adjustment: 180 mm (9 stages)

METHOD FOR ADJUSTING AIR SUSPENSION SEAT HARDNESS

Air suspension seat (if equipped)
Operate the suspension switch (9) to adjust the hardness of the suspension.

• If you press the suspension switch (9), the suspension be-

comes hard.

• If you pull the suspension switch (9), the suspension be-

comes soft. (Air release sound is heard.)

Weight adjustment range: 60 to 150 kg

METHOD FOR HEATING SEAT

Heated seat (if equipped)
Turn the seat heater switch ON.
(a): OFF position
(b): ON position
The seat cushion and backrest become warm.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-164

«
...
234
235
236
237
238
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: jcb Страницы: 51

Бренд: Daewoo Страницы: 656

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды