Komatsu HB365LC-3 Скачать руководство пользователя страница 345 | Manualshive

Страница: 345 / 506

background image

Problem

Main causes

Remedy

Engine does not start.
(“L04” lights up on monitor.)

Damaged data in the controller

Check, repair. (*)

Other system troubles

Check, repair. (*)

PHENOMENA AND ACTIONS FOR CHASSIS

• For the remedies indicated with (*) in the remedy column, always contact your Komatsu distributor.
• In cases of problems or causes which are not listed below, ask your Komatsu distributor for repairs.

Problem

Main causes

Remedy

Speed of travel, swing, boom, arm,
bucket is slow

Lack of hydraulic oil

Set oil to specified level. See
CHECKS BEFORE STARTING.

Pump generates abnormal noise.
(sucking in air)

Clogged element in hydraulic tank
strainer, lack of oil

Clean. See EVERY 2000 HOURS
MAINTENANCE.

Excessive rise in hydraulic oil temper-
ature

Dirty oil cooler

Clean. See EVERY 500 HOURS
MAINTENANCE.

Lack of hydraulic oil

Set oil to specified level. See
CHECKS BEFORE STARTING.

Track comes off.

Track too loose

Adjust track tension, see WHEN RE-
QUIRED.

Abnormal wear of sprocket

Track too loose

Adjust track tension, see WHEN RE-
QUIRED.

Boom rises slowly or does not rise.

Lack of hydraulic oil

Set oil to specified level. See
CHECKS BEFORE STARTING.

Does not swing.

Swing lock switch still applied

Turn swing lock switch OFF.

Swing brake system error

Check, adjust. (*)

When move of machine to safe place
is required, turn the swing parking
brake cancel switch to ON position
temporarily.

PHENOMENA AND ACTIONS FOR ENGINE RELATED PARTS

• For the remedies indicated with (*) in the remedy column, always contact your Komatsu distributor.
• In cases of problems or causes which are not listed below, ask your Komatsu distributor for repairs.

Problem

Main causes

Remedy

Engine oil pressure caution lamp
lights up.

Lowered oil level in engine oil pan
(sucking in air)

Set oil to specified level. See
CHECKS BEFORE STARTING.

Improper oil is used. (Viscosity is im-
proper.)

Replace oil. See METHOD FOR US-
ING FUEL, COOLANT AND LUBRI-
CANTS ACCORDING TO AMBIENT
TEMPERATURE.

Clogged oil filter cartridge

Replace cartridge. See EVERY 500
HOURS MAINTENANCE.

Oil leakage due to improper connec-
tion or breakage of oil pipe or pipe
joint

Check, repair. (*)

Defective engine oil pressure sensor

Replace sensor. (*)

Defective monitor

Replace monitor. (*)

OPERATION

TROUBLES AND ACTIONS

3-273

«
...
343
344
345
346
347
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: Otis Elevator Страницы: 60

PC600-8R BACKHOE

Бренд: Komatsu Страницы: 10

Бренд: SANY Страницы: 166

Бренд: SANY Страницы: 276

Бренд: Savaria Страницы: 28

Бренд: Super Products Страницы: 126

Бренд: BOXER Страницы: 48

Бренд: Komatsu Страницы: 1043

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды