Komatsu HB365LC-3 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 506

background image

Warning when swinging or travelling in reverse

(16) Warning when swinging or travelling in reverse (09833-
A0881)

k

k

WARNING

• When swinging or backing up excavator, press button

to change display mode on monitor so you can see
rear and side of the machine.
Before moving, look around and at mirror and monitor
to confirm that no one is around the machine. Failure
to do so can result in serious injury or death.

Caution for blast jobsite

(17) Caution of an explosive hazard caused by active radio
transmitter at a blast zone (09845-00480).

• Keep machine at a safe distance from blast zone and a

detonator.

Caution for high-pressure fuel

(18) Caution for high-pressure fuel (6271-81-2980).

Warning for handling ROPS

(19) Caution for machine with ROPS (09620-T2001, 09620-
A3001)

• If any modification is applied to the ROPS, it may affect the

strength and may not comply with the standard.

• ROPS may provide less protection if it has been structural-

ly damaged or involved in roll-over.

• Always wear seat belt when moving.

SAFETY

SAFETY LABELS

2-15

«
...
33
34
35
36
37
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: CASE CONSTRUCTION Страницы: 256

Бренд: OLEO Страницы: 12

Бренд: IHI Страницы: 110

Бренд: Kubota Страницы: 90

Бренд: Case Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды