Komatsu HB365LC-3 Скачать руководство пользователя страница 405 | Manualshive

Страница: 405 / 506

background image

16. Install the cover (8) on the bottom of the fuel tank. (if

equipped)

17. After completing the replacement of filter cartridge (4),

bleed air from the fuel circuit.

REMARK

For bleeding air, see “PROCEDURES FOR BLEEDING
AIR FROM FUEL CIRCUIT (3-262)”.

METHOD FOR CHECKING SWING PINION GREASE LEVEL, ADD GREASE

Items to be prepared
Scale
1.

Swing 3 times each to the right and left, and stop the machine.

2.

Remove bolts (1) (2 pieces) on the top of the revolving
frame, and remove cover (2).

3.

Insert ruler (3) into the grease through inspection and ad-
justment hole (A). Check that the height of grease (S) in
the area where the pinion passes is at least 20 mm.
Add grease if the grease amount (S) is less than 20 mm.

4.

Check that the grease is not milky white.
Total amount of grease: 33 ℓ(29.7 kg)
If the grease is milky white, it needs to be replaced. Ask
your Komatsu distributor to replace it.

5.

Install cover (2) with bolt (1).

MAINTENANCE

MAINTENANCE PROCEDURE

4-57

«
...
403
404
405
406
407
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: Hitachi Страницы: 183

Zaxis 110 Zaxis 125US

Бренд: Hitachi Страницы: 41

ZAXIS 120-3 class

Бренд: Hitachi Страницы: 461

Бренд: Hitachi Страницы: 41

Бренд: Savaria Страницы: 48

Бренд: JackRabbit Страницы: 38

Бренд: jcb Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды