Komatsu HB365LC-3 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 506

background image

• Set up labels to inform of road edges and soft ground. If the visibility is not good, position a conductor if

necessary. Operator should pay careful attention to the labels and follow the instructions from the conduc-
tor.

• Only one signalman should give signals.
• Make sure that all workers understand the meaning of all signals, signs, and labels before starting work.

BEWARE OF ASBESTOS DUST

Asbestos dust in the air can cause lung cancer if it is inhaled.
There is danger of inhaling asbestos when working on jobsite
where demolition work is performed or industrial waste is han-
dled. Always observe the following.

• Spray water to keep down the dust.
• Do not use compressed air.
• If there is danger that there may be asbestos dust in the

air, always operate the machine from an upwind position,
and make sure that all workers operate on the upwind
side.

• All workers should use anti-dust masks.
• Prohibit other personnel from coming close to the machine during operation.
• Always observe the regulations for jobsite and environmental standards.

This machine does not contain asbestos, but any part which is not the genuine part, it has risk of containing
asbestos. Always use Komatsu genuine parts.

START ENGINE

USE WARNING TAGS

If  there  is  a  “DANGER!  Do  NOT  operate!”  warning  tag  dis-
played,  it  means  that  someone  is  performing  inspection  and
maintenance of the machine. If the warning tag is ignored and
the  machine  is  operated,  the  person  performing  inspection  or
maintenance  may  be  caught  in  the  rotating  parts  or  moving
parts. It is dangerous and may cause serious personal injury or
death. Do not start the engine or touch the levers.

,&

PRECAUTIONS FOR OPERATION

SAFETY

2-30

«
...
48
49
50
51
52
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: Case Страницы: 292

Бренд: SANY Страницы: 208

Бренд: Daewoo Страницы: 151

Бренд: jcb Страницы: 28

Бренд: Super Products Страницы: 126

Бренд: RHINO Страницы: 42

Бренд: Menzi Muck Страницы: 74

Бренд: LOFTNESS Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды