Kollmorgen Sercos II Скачать руководство пользователя страница 111

Страница: 111 / 134

4.8

Homing

4.8.1

Drive-controlled

If all ASCII parameters are set in such a way that the reference run (homing) works per-
fectly without sercos

, for example via the startup software (note incremental scaling via

sercos

), the drive-controlled reference run can be started using the command IDN148.

IDN used

Meaning

ASCII Parameter

IDN 41

Homing speed

VREF

IDN 42

Homing acceleration

ACCR, DECR

IDN 47

Position setpoint

IDN 52

Reference distance 1 (motor feedback)

ROFFS

IDN 54

Reference distance 2 (external feedback)

ROFFS

IDN 147

Homing parameter

NREF

IDN 148

Command: Amplifier-Controlled Homing

IDN 300 (x=0...3) Configuration DIGITAL-In 1...4

INxMODE

IDN 403

Position Feedback Value Status

IDNP 3004

Position Switch Configuration

SWCNFG

IDNP 3027

Homing mode according to ASCII object
reference

NREF

IDNP 3067

REFMODE

IDNP 3068

DREF

Drive-controlled referencing

Sequence

IDN

Meaning

Master sets and releases

IDN 148

Drive-controlled referencing

The cyclical target values are ignored as long
as IDN 148 is active.
Drive deletes the "Position Feedback Value
Status" bit

IDN 403

Position Feedback Value
Status

The drive switches to internal position control
The drive accelerates

IDN 42

Homing acceleration

To final speed for Homing

IDN 41

Homing speed

Further settings for Homing

(IDN 147)

Homing Parameters

Homing mode (see ASCII object reference)

IDNP 3027

REFMODE

IDNP 3067 Source of the zero impulse

The drive brakes behind the position encoder ref.

mark and stops at the ref. point

IDN 42

Reference run acceleration

The target position values are based on the
ref. mark.

IDN 47

Position setpoint

If the drive is at standstill and the actual positi-
on values are based on the ref point.

IDN 403

Position Feedback Value
Status

Homing is completed (bit = 0)

IDN 148

Drive-controlled referencing

ROFFS

(IDN 52)

Reference distance 1 (motor
feedback)

ROFFS

(IDN 54)

Reference distance 2 (exter-
nal feedback)

Once homing has been successfully completed, the drive follows the target values.
Should homing be interrupted, the actual position values are not based on the ref mark,
and the bit for the status of actual position values remains at a low level.

sercos

for S300/S700

111

Kollmorgen

04/2016

Appendix

Содержание Sercos II







































































































































Результаты поиска

Содержание Sercos II

Отзывы:

Похожие инструкции для Sercos II

Бренды по названию

Популярные бренды

Kollmorgen Sercos II, Перевод оригинального руководства

Результаты поиска

Содержание Sercos II

Отзывы:

Похожие инструкции для Sercos II

Бренды по названию

Популярные бренды