Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 432

background image

Getting Started

1

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

41

Front Panel Overlays for Different Languages

Front panel overlays, which have translations for the English front panel keys and

label text, are available in 10 languages. The appropriate overlay is included when

the localization option is chosen at time of purchase.

To install a front panel overlay:

18.

Demo 2, Ground, and

Demo 1 terminals

•

Demo 2 terminal — This terminal outputs the Probe Comp signal which helps you match a

probe's input capacitance to the oscilloscope channel to which it is connected. See

"Compensate Passive Probes"

on page 34. With certain licensed features, the

oscilloscope can also output demo or training signals on this terminal.

•

Ground terminal — Use the ground terminal for oscilloscope probes connected to the Demo

1 or Demo 2 terminals.

•

Demo 1 terminal — With certain licensed features, the oscilloscope can output demo or

training signals on this terminal.

19.

USB Host port

This port is for connecting USB mass storage devices or printers to the oscilloscope.
Connect a USB compliant mass storage device (flash drive, disk drive, etc.) to save or recall

oscilloscope setup files and reference waveforms or to save data and screen images. See

, “Save/Recall (Setups, Screens, Data),” starting on page 273.

To print, connect a USB compliant printer. For more information about printing see

, “Print (Screens),” starting on page 285.

You can also use the USB port to update the oscilloscope's system software when updates are

available.
You do not need to take special precautions before removing the USB mass storage device

from the oscilloscope (you do not need to "eject" it). Simply unplug the USB mass storage

device from the oscilloscope when the file operation is complete.

CAUTION:

Do not connect a host computer to the oscilloscope's USB host port.

Use the

device port. A host computer sees the oscilloscope as a device, so connect the host computer

to the oscilloscope's device port (on the rear panel). See

"I/O Interface Settings"

page 291.
There is a second USB host port on the back panel.

20.

Digital channel

inputs

Connect the digital probe cable to this connector (MSO models only). See

Channels,” starting on page 105.

21.

Waveform generator

output

Outputs sine, square, ramp, pulse, DC, or noise on the Gen Out BNC. Press the

[Wave Gen]

key

to set up the waveform generator. See

, “Waveform Generator,” starting on page

«
...
39
40
41
42
43
...
»

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniiVision 3000 X Series

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: NEC Страницы: 54

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: Modulate Страницы: 2

Бренд: PANDROL Страницы: 36

Бренд: Badger Basket Страницы: 7

Бренд: Backyard Discovery Страницы: 53

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: DBX Bushido Страницы: 12

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды