Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 330

Страница: 330 / 432

330

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Reference

EDK

Educator's Kit
Provides training signals on the oscilloscope's Demo

terminals and a lab guide/tutorial for education

environments.

Now standard.

EMBD

Embedded Serial Triggering and Analysis (I2C, SPI).

Order D3000GENA (replaces DSOX3EMBD

and others).

FLEX

FlexRay Triggering and Analysis.

Order D3000AUTA (replaces DSOX3FLEX and

others).

MASK

Mask Limit Test
Lets you create a mask and test waveforms to determine

whether they comply to the mask.

Order D3000GENA, D3000AUTA,

D3000AERA, or D3000PWRA (which include

and replace DSOX3MASK).

mem4M

Memory Upgrade.
It shows the total memory depth (4 Mpts interleaved).

Order DSOX3MEMUP.

MSO

Mixed Signal Oscilloscope (MSO). Upgrade a DSO to an

MSO.
Adds 16 digital channels. You do not have to install any

hardware.

Order DSOX3MSO for 500 MHz and lower

bandwidth models or DSOXPERFMSO for

1 GHz bandwidth models.
The digital probe cable kit is supplied with

the MSO license.

PWR

Power Measurement and Analysis.

Order D3000PWRA (replaces DSOX3PWR

and others).
You can find the

DSOX3PWR Power

Measurement Application User's Guide

www.keysight.com/find/3000X-Series

-manual

or on the Documentation CD.

SGM

Segmented Memory.
Lets you capture infrequent or burst signals with great

resolution by eliminating the capture of your signal's

"inactivity".

Order DSOX3SGM.

VID

Extended Video Triggering and Analysis.

Order D3000GENA (replaces DSOX3VID and

others).

WAVEGEN

Waveform Generator.

Order DSOX3WAVEGEN.

Table 4

Licensed Options Available (continued)

License

Description

After purchase model number, notes

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды