Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 417

Страница: 417 / 432

UART/RS232 Triggering and Serial Decode

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

417

UART/RS232 Triggering

To set up the oscilloscope to capture UART/RS-232 signals, see

"Setup for

UART/RS232 Signals"

on page 415.

To trigger on a UART (Universal Asynchronous Receiver/Transmitter) signal

connect the oscilloscope to the Rx and Tx lines and set up a trigger condition.

RS232 (Recommended Standard 232) is one example of a UART protocol.

Press

[Trigger]

In the Trigger Menu, press the

Trigger

softkey; then, turn the Entry knob to

select the serial slot (Serial 1 or Serial 2) on which the UART/RS232 signals are

being decoded.

Press the

Trigger Setup

softkey to open the UART/RS232 Trigger Setup Menu.

Press the

Base

softkey to select Hex or ASCII as the base displayed on the Data

softkey in the UART/RS232 Trigger Setup Menu.

Note that the setting of this softkey does not affect the selected base of the

decode display.

Press the

Trigger

softkey and set up the desired trigger condition:

•

Rx Start Bit

— The oscilloscope triggers when a start bit occurs on Rx.

•

Rx Stop Bit

— Triggers when a stop bit occurs on Rx. The trigger will occur on

the first stop bit. This is done automatically whether the device under test

uses 1, 1.5, or 2 stop bits. You do not need to specify the number of stop bits

used by the device Under test.

•

Rx Data

— Triggers on a data byte that you specify. For use when the device

under test data words are from 5 to 8 bits in length (no 9th (alert) bit).

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды