Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 294

Страница: 294 / 432

294

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Utility Settings

Configure the oscilloscope's LAN interface:

Press the

Addresses

softkey.

Use the

Modify

softkey (and the other softkeys and the Entry knob) to enter

the IP Address, Subnet Mask, Gateway IP, and DNS IP values. When you are

done, go back up in the menu hierarchy.

Press the

Host name

softkey. Use the softkeys and the Entry knob to enter the

Host name. When you are done, go back up in the menu hierarchy.

Press the

Apply

softkey.

Connect the oscilloscope to the local area network (LAN) by inserting the LAN

cable into the "LAN" port on the rear panel of the oscilloscope.

Stand-alone (Point-to-Point) Connection to a PC

The following procedure describes how to establish a point-to-point (stand alone)

connection to the oscilloscope. This is useful if you want to control the

oscilloscope using a laptop computer or a stand-alone computer.

Press

[Utility] > I/O

Press the

LAN Settings

softkey.

Press the

Config

softkey; then, turn the Entry knob to select

Automatic

, and press

the softkey again to enable it.

If your network supports DHCP or AutoIP, enabling

Automatic

lets the

oscilloscope use those services to get its LAN configuration settings

Connect your PC to the oscilloscope using a cross-over LAN cable such as

Keysight part number 5061-0701, available on the web at

www.keysight.com/find/parts

Cycle power on the oscilloscope. Wait until the LAN connection is configured:

•

Press

[Utility] > I/O

and wait until the LAN status shows "configured".

This may take a few minutes.

Now, the instrument is connected, and the instrument's web interface or remote

control via LAN may be used.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды