Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 257

Страница: 257 / 432

257

Keysight InfiniiVision 3000 X-Series Oscilloscopes

User's Guide

17 Waveform Generator

To select generated waveform types and settings / 257
To edit arbitrary waveforms / 261
To output the waveform generator sync pulse / 265
To specify the expected output load / 266
To use waveform generator logic presets / 266
To add noise to the waveform generator output / 267
To add modulation to the waveform generator output / 267
To restore waveform generator defaults / 272

A waveform generator is built into the oscilloscope. It is enabled by Option WGN

or the DSOX3WAVEGEN upgrade. The waveform generator gives you an easy way

to provide input signals when testing circuitry with the oscilloscope.

Waveform generator settings can be saved and recalled with oscilloscope setups.

See

Chapter 18

, “Save/Recall (Setups, Screens, Data),” starting on page 273.

To select generated waveform types and settings

To access the Waveform Generator Menu and enable or disable the waveform

generator output on the front panel Gen Out BNC, press the

[Wave Gen]

key.

When waveform generator output is enabled, the

[Wave Gen]

key is illuminated.

When waveform generator output is disabled, the

[Wave Gen]

key is off.

The waveform generator output is always disabled when the instrument is first

turned on.

The waveform generator output is automatically disabled if excessive voltage is

applied to the Gen Out BNC.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды