Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 132

Страница: 132 / 432

132

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Display Settings

To erase the results of previous acquisitions from the display, press the

Clear

Persistence

softkey.

The oscilloscope will start to accumulate acquisitions again.

To return the oscilloscope to the normal display mode, turn off persistence;

then, press the

Clear Persistence

softkey.

Turning off persistence does not clear the display. The display is cleared if you

press the

Clear Display

softkey or if you press the

[AutoScale]

key (which also

turns off persistence).

For another method of seeing worst-case extremes of varying waveforms, see

"Glitch or Narrow Pulse Capture"

on page 191.

To clear the display

Press

[Display] > Clear Display

You can also configure the

[Quick Action]

key to clear the display. See

"Configuring

the [Quick Action] Key"

on page 307.

To select the grid type

When the

Video

trigger type is selected (see

"Video Trigger"

on page 160), and the

vertical scaling of at least one displayed channel is 140 mV/div, the

Grid

softkey

lets you select from these grid types:
•

Full

— the normal oscilloscope grid.

•

— shows vertical grids, labeled on the left, from -0.3 V to 0.8 V.

•

IRE

— (Institute of Radio Engineers) shows vertical grids in IRE units, labeled on

the left, from -40 to 100 IRE. The 0.35 V and 0.7 V levels from the

grid are

also shown and labeled at the right. When the

IRE

grid is selected, cursor values

are also shown in IRE units. (Cursor values via the remote interface are not in

IRE units.)

The

and

IRE

grid values are accurate (and match Y cursor values) when the

vertical scaling is 140 mV/division and the vertical offset is 245 mV.

To select the grid type:

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды