Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 265

Страница: 265 / 432

Waveform Generator

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

265

Capturing Other Waveforms to the Arbitrary Waveform

The Edit Waveform Menu is opened by pressing

Edit Waveform

in the main

Waveform Generator Menu.

To capture another waveform to the arbitrary waveform:

Press

Source

; then, use the Entry knob to select the analog channel, math, or

reference location whose waveform you wish to capture.

Press

Store Source to Arb

The source waveform is decimated into 8192 (maximum) or fewer arbitrary

waveform points.

To output the waveform generator sync pulse

If the Waveform Generator Menu is not currently displayed on the

oscilloscope's softkeys, press the

[Wave Gen]

key.

In the Waveform Generator Menu, press the

Settings

softkey.

In the Waveform Generator Settings Menu, press the

Trig Out

softkey and turn

the Entry knob to select

Waveform Generator Sync Pulse

CAUTION

When you create a new arbitrary waveform, the existing arbitrary waveform definition is

overwritten. Note that you can use the

[Save/Recall]

key and menu to save arbitrary

waveforms to one of four internal storage locations or to a USB storage device, and you

can recall them later. See

"To save arbitrary waveforms"

on page 279 an d

"To

recall arbitrary waveforms"

on page 283.

NOTE

If the source waveform frequency and/or voltage exceed the capabilities of the waveform

generator, the arbitrary waveform will be limited to the capabilities of the waveform

generator. For example, a 20 MHz waveform captured as the arbitrary waveform, becomes a

12 MHz waveform.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды