Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 235

Страница: 235 / 432

Measurements

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

235

From the Measurement Menu, press the

Settings

softkey; then, press the

Thresholds

softkey to set analog channel measurement thresholds.

You can also open the Measurement Threshold Menu by pressing

[Analyze] >

Features

and then selecting

Measurement Thresholds

Press the

Source

softkey to select the analog channel or math waveform source

for which you want to change measurement thresholds.

Each analog channel and the math waveform can be assigned unique threshold

values.

Press the

Type

softkey to set the measurement threshold to

(percentage of

Top and Base value) or to

Absolute

(absolute value).

•

Percentage thresholds can be set from 5% to 95%.

•

The units for absolute threshold for each channel is set in the channel probe

menu.

•

When the

Source

is set to

Math: f(t)

, the threshold

Type

can only be set to

Percent

Press the

Lower

softkey; then, turn the Entry knob to set the lower measurement

threshold value.

Increasing the lower value beyond the set middle value will automatically

increase the middle value to be more than the lower value. The default lower

threshold is 10% or 800 mV.

If threshold

Type

is set to

, the lower threshold value can be set from 5% to

93%.

TIP

Absolute threshold hints

•

Absolute thresholds are dependent on channel scaling, probe attenuation, and probe units. Always

set these values first before setting absolute thresholds.

•

The minimum and maximum threshold values are limited to on-screen values.

•

If any of the absolute threshold values are above or below the minimum or maximum waveform

values, the measurement may not be valid.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды