Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 214

Страница: 214 / 432

214

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Measurements

After all measurements have been cleared, when

[Meas]

is pressed again, the

default measurements will be Frequency and Peak-Peak.

Measurements Summary

The automatic measurements provided by the oscilloscope are listed in the

following table. All measurements are available for analog channel waveforms. All

measurements except Counter are available for reference waveforms and math

waveforms other than FFT. A limited set of measurements is available for math FFT

waveforms and for digital channel waveforms (as described in the following table).

Measurement

Valid

for

Math

FFT

Valid for

Digital

Channels

Notes

Yes, Full

Screen

Yes

Yes

Not valid for math waveforms.

"Delay"

on page 229

Measures between two sources.

Press

Settings

to specify the second

source.

Yes

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды