Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 285

Страница: 285 / 432

285

Keysight InfiniiVision 3000 X-Series Oscilloscopes

User's Guide

19 Print (Screens)

To print the oscilloscope's display / 285
To set up network printer connections / 286
To specify the print options / 288
To specify the palette option / 288

You can print the complete display, including the status line and softkeys, to a

USB printer or a network printer when the DSOXLAN LAN/VGA module is

installed.

The Print Configuration Menu is displayed when you press the

[Print]

key. The print

option softkeys and the

Press to Print

softkey are ghosted (not available) until a

printer is connected.

To print the oscilloscope's display

Connect a printer. You can:

•

Connect a USB printer to either the USB port on the front panel or the

rectangular USB host port on the rear panel.

For the most up-to-date listing of printers that are compatible with the

InfiniiVision oscilloscopes, please visit

www.keysight.com/find/InfiniiVision-printers

•

Set up a network printer connection. See

"To set up network printer

connections"

on page 286.

Press the

[Print]

key on the front panel.

In the Print Configuration Menu, press the

Print to

softkey; then, turn the Entry

knob to select the desired printer.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды