Keysight Technologies InfiniiVision 3000 X Series Скачать руководство пользователя страница 105

Страница: 105 / 432

105

Keysight InfiniiVision 3000 X-Series Oscilloscopes

User's Guide

6 Digital Channels

To connect the digital probes to the device under test / 105
Acquiring waveforms using the digital channels / 109
To display digital channels using AutoScale / 109
Interpreting the digital waveform display / 110
To switch all digital channels on or off / 112
To switch groups of channels on or off / 112
To switch a single channel on or off / 112
To change the displayed size of the digital channels / 111
To reposition a digital channel / 113
To change the logic threshold for digital channels / 112
To display digital channels as a bus / 114
Digital channel signal fidelity: Probe impedance and grounding / 117

This chapter describes how to use the digital channels of a Mixed-Signal

Oscilloscope (MSO).

The digital channels are enabled on MSOX3000 X-Series models and

DSOX3000 X-Series models that have the MSO upgrade license installed.

To connect the digital probes to the device under test

If necessary, turn off the power supply to the device under test.

Turning off power to the device under test would only prevent damage that

might occur if you accidentally short two lines together while connecting

probes. You can leave the oscilloscope powered on because no voltage appears

at the probes.

Содержание InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 3000 X Series, Руководство пользователя

Результаты поиска

Содержание InfiniiVision 3000 X Series

Отзывы:

Похожие инструкции для InfiniiVision 3000 X Series

Бренды по названию

Популярные бренды