Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 245

Страница: 245 / 378

245

Keysight InfiniiVision 2000 X-Series Oscilloscopes

User's Guide

17 Waveform Generator

To select generated waveform types and settings / 245
To output the waveform generator sync pulse / 248
To specify the expected output load / 248
To use waveform generator logic presets / 249
To add noise to the waveform generator output / 250
To add modulation to the waveform generator output / 250
To restore waveform generator defaults / 255

A waveform generator is built into the oscilloscope. It is enabled by Option WGN

or the DSOX2WAVEGEN upgrade. The waveform generator gives you an easy way

to provide input signals when testing circuitry with the oscilloscope.

Waveform generator settings can be saved and recalled with oscilloscope setups.

See

Chapter 18

, “Save/Recall (Setups, Screens, Data),” starting on page 257.

To select generated waveform types and settings

To access the Waveform Generator Menu and enable or disable the waveform

generator output on the front panel Gen Out BNC, press the

[Wave Gen]

key.

When waveform generator output is enabled, the

[Wave Gen]

key is illuminated.

When waveform generator output is disabled, the

[Wave Gen]

key is off.

The waveform generator output is always disabled when the instrument is first

turned on.

The waveform generator output is automatically disabled if excessive voltage is

applied to the Gen Out BNC.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды