Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 291

Страница: 291 / 378

Utility Settings

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

291

Point your web browser to:

www.keysight.com/find/warrantystatus

Enter your product's model number and serial number. The system will search

for the warranty status of your product and display the results. If the system

cannot find your product's warranty status, select

Contact Us

and speak with a

Keysight Technologies representative.

To contact Keysight

Information on contacting Keysight Technologies can be found at:

www.keysight.com/find/contactus

To return the instrument

Before shipping the oscilloscope to Keysight Technologies, contact your nearest

Keysight Technologies sales or service office for additional details. Information on

contacting Keysight Technologies can be found at:

www.keysight.com/find/contactus

Write the following information on a tag and attach it to the oscilloscope.

•

Name and address of owner.

•

Model number.

•

Serial number.

•

Description of service required or failure indication.

Remove accessories from the oscilloscope.

Only return accessories to Keysight Technologies if they are associated with the

failure symptoms.

Package the oscilloscope.

You can use the original shipping container, or provide your own materials

sufficient to protect the instrument during shipping.

Seal the shipping container securely, and mark it FRAGILE.

Configuring the [Quick Action] Key

The

[Quick Action]

key lets you perform common, repetitive actions by pressing a

single key.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды