Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 279

Страница: 279 / 378

Utility Settings

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

279

File Explorer

The File Explorer lets you navigate the oscilloscope's internal file system and the

file systems of connected USB storage devices.

From the internal file system, you can load oscilloscope setup files or mask files.

From a connected USB storage device, you can load setup files, mask files, license

files, firmware update (*.ksx) files, label files, etc. Also, you can delete files on a

connected USB storage device.

The oscilloscope's internal file system, under "\User Files", consists of 10 locations

for oscilloscope setup files, and four locations for mask files.

To use the File Explorer:

Press

[Utility] > File Explorer

In the File Explorer Menu, press the softkey in the first position and use the

Entry knob to navigate.

NOTE

The USB port on the front panel, and the USB port on the rear panel labeled "HOST" are USB

Series A receptacles. These are the receptacles to which you can connect USB mass storage

devices and printers.
The square receptacle on the rear panel labeled "DEVICE" is provided for controlling the

oscilloscope over USB. See the

Programmer's Guide

for more information.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды