Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 271

Страница: 271 / 378

Print (Screens)

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

271

In the Print Configuration Menu, press the

Print to

softkey; then, turn the Entry

knob to select the network printer you want to configure (either #0 or #1).

Press the

Network Setup

softkey.

In the Network Printer Setup Menu, press the

Modify

softkey; then, turn the

Entry knob to select the network parameter you want to enter.

The setting that must be entered is:

•

Printer Address

— this is the printer or print server's address in one of the

following formats:

•

IP address of a network-enabled printer (for example: 192.168.1.100 or

192.168.1.100:650). Optionally, a non-standard port number can be

specified following a colon.

•

IP address of a print server followed by the path to the printer (for

example: 192.168.1.100/printers/printer-name or

192.168.1.100:650/printers/printer-name).

•

Path to a Windows network printer share (for example: \\server\share).

When the Printer Address is a Windows network printer share, the

Modify

softkey also lets you enter these settings:

•

Network Domain

— this is the Windows network domain name.

•

Username

— this is your login name for the Windows network domain.

•

Password

— this is your login password for the Windows network domain.

To clear an entered password, press the

Clear Password

softkey.

Use the

Spell

Enter

, and

Delete Character

softkeys to enter the network printer

settings:

•

Spell

— press this softkey and turn the entry knob to select the character at

the current position.

•

Enter

— press this softkey to enter characters and move the cursor to the next

character position.

•

Delete Character

— press the

Enter

softkey until the desired character is

highlighted; then, press this softkey to delete the character.

NOTE

You can use a connected USB keyboard instead of using the

Spell

(and other) character

editing softkeys.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды