Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 277

Страница: 277 / 378

Utility Settings

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

277

To establish a LAN connection

Automatic

Configuration

Press

[Utility] > I/O

Press the

LAN Settings

softkey.

Press the

Config

softkey; then, turn the Entry knob to select

Automatic

, and press

the softkey again to enable it.

If your network supports DHCP or AutoIP, enabling

Automatic

lets the

oscilloscope use those services to get its LAN configuration settings

If your network provides Dynamic DNS, you can enable the

Dynamic DNS

option

to let the oscilloscope register its hostname and use the DNS server for name

resolution.

You can enable the

Multicast DNS

option to let the oscilloscope use Multicast

DNS for name resolution on small networks without a conventional DNS server.

Connect the oscilloscope to the local area network (LAN) by inserting the LAN

cable into the "LAN" port on the rear panel of the oscilloscope.

In a few moments the oscilloscope will connect to the network automatically.

If the oscilloscope does not automatically connect to the network, press

[Utility]

> I/O > LAN Reset

. In a few moments the oscilloscope will connect to the

network.

Manual

Configuration

Get the oscilloscope's network parameters (host name, IP address, subnet

mask, gateway IP, DNS IP, etc.) from your network administrator.

Press

[Utility] > I/O

Press the

LAN Settings

softkey.

Press the

Config

softkey; then, turn the Entry knob to select

Automatic

, and press

the softkey again to disable it.

NOTE

When you connect the oscilloscope to a LAN it is a good practice to limit access to the

oscilloscope by setting a password. By default, the oscilloscope is not password protected.

See

"Setting a Password"

on page 305 to set a password.

NOTE

Any time you modify the oscilloscope's hostname, it breaks the connection between the

oscilloscope and the LAN. You need to re-establish communication to the oscilloscope using

the new hostname.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды