Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 330

Страница: 330 / 378

330

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

CAN/LIN Triggering and Serial Decode

Press the

Trigger:

softkey; then, turn the Entry knob to select the trigger

condition:

•

SOF - Start of Frame

— The oscilloscope triggers at the start of a frame.

•

Remote Frame ID (RTR)

— The oscilloscope triggers on remote frames with the

specified ID. Press the

Bits

softkey to select the ID.

•

Data Frame ID (~RTR)

— The oscilloscope will trigger on data frames matching

the specified ID. Press the

Bits

softkey to select the ID.

•

Remote or Data Frame ID

— The oscilloscope will trigger on remote or data

frames matching the specified ID. Press the

Bits

softkey to select the ID.

•

Data Frame ID and Data

— The oscilloscope will trigger on data frames

matching the specified ID and data. Press the

Bits

softkey to select the ID

and set up the number of data bytes and values.

•

Error Frame

— The oscilloscope will trigger on CAN active error frames.

•

All Errors

— The oscilloscope will trigger when any form error or active error is

encountered.

•

Acknowledge Error

— The oscilloscope will trigger when the acknowledge bit is

recessive (high).

•

Overload Frame

— The oscilloscope will trigger on CAN overload frames.

If you select a condition that lets you trigger on ID or data values, use the

Bits

softkey and the CAN Bits Menu to specify those values.

For details about using the CAN Bits Menu softkeys, press and hold the softkey

in question to display the built-in help.

You can use the

Zoom

mode for easier navigation of the decoded data.

NOTE

If the setup does not produce a stable trigger, the CAN signal may be slow enough that the

oscilloscope is AutoTriggering. Press the

[Mode/Coupling]

key, then press the

Mode

softkey

to set the trigger mode from

Auto

Normal

NOTE

To display CAN serial decode, see

"CAN Serial Decode"

on page 331.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды