Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 70

Страница: 70 / 378

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Math Waveforms

f(t)

is not already shown on the

Function

softkey, press the

Function

sofkey and

select

f(t): Displayed

Use the

Operator

softkey to select an operator or transform.

For more information on the operators, see:

•

•

•

•

"Math Visualizations"

on page 91

Use the

Source 1

softkey to select the analog channel on which to perform

math. You can rotate the Entry knob or repetitively press the

Source 1

softkey to

make your selection. If you choose a transform function (differentiate, integrate,

FFT, or square root) the result is displayed.

If you select an arithmetic operator, use the

Source 2

softkey to select the

second source for the arithmetic operation. The result is displayed.

To re-size and re-position the math waveform, see

"To adjust the math

waveform scale and offset"

on page 71.

TIP

Math Operating Hints

If the analog channel or math function is clipped (not fully displayed on screen) the resulting

displayed math function will also be clipped.
Once the function is displayed, the analog channel(s) may be turned off for better viewing of

the math waveform.
The vertical scaling and offset of each math function can be adjusted for ease of viewing and

measurement considerations.
The math function waveform can be measured using

[Cursors]

and/or

[Meas]

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды