Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 175

Страница: 175 / 378

Trigger Mode/Coupling

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

175

The external trigger input impedance is 1M Ohm. This lets you use passive probes

for general-purpose measurements. The higher impedance minimizes the loading

effect of the oscilloscope on the device under test.

To set the EXT TRIG IN units and probe attenuation:

Press the

[Mode/Coupling]

key in the Trigger section of the front panel.

In the Trigger Mode and Coupling Menu, press the

External

softkey.

In the External Trigger Menu, press the

Units

softkey to select between:

•

Volts

— for a voltage probe.

•

Amps

— for a current probe.

Measurement results, channel sensitivity, and the trigger level will reflect the

measurement units you have selected.

Press the

Probe

softkey; then, turn the entry knob to specify the probe

attenuation.

The attenuation factor can be set from 0.001:1 to 10000:1 in a 1-2-5 sequence.

The probe attenuation factor must be set properly for measurements to be

made correctly.

CAUTION

Maximum voltage at oscilloscope external trigger input

300 Vrms, 400 Vpk
1 M ohm input: For steady-state sinusoidal waveforms derate at 20 dB/decade above

57 kHz to a minimum of 5 Vpk

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды