Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 72

Страница: 72 / 378

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Math Waveforms

A scale unit of

(undefined) will be displayed for math functions when two source

channels are used and they are set to dissimilar units and the combination of units

cannot be resolved.

Math Operators

Math operators perform arithmetic operations (add, subtract, or multiply) on

analog input channels.
•

•

Add or Subtract

When you select add or subtract, the

Source 1

and

Source 2

values are added or

subtracted point by point, and the result is displayed.

You can use subtract to make a differential measurement or to compare two

waveforms.

If your waveforms' DC offsets are larger than the dynamic range of the

oscilloscope's input channels you will need to use a differential probe instead.

Math function

Units

add or subtract

V or A

multiply

, A

, or W (Volt-Amp)

d/dt

V/s or A/s (V/second or A/second)



Vs or As (V-seconds or A-seconds)

FFT

dB* (decibels). See also

"FFT Units"

page 84.

√

(square root)

1/2

, A

1/2

, or W

1/2

(Volt-Amp)

* When the FFT source is channel 1, 2, 3 or 4, FFT units will be displayed in dBV when channel units

is set to Volts and channel impedance is set to 1 M

Ω

. FFT units will be displayed in dBm when

channel units is set to Volts and channel impedance is set to 50

Ω

. FFT units will be displayed as dB

for all other FFT sources or when a source channel's units has been set to Amps.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды