Keeler IntelliPuff Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 51

background image

Intellipuff Service Manual

Page 31 of 51

Issue D 27/02/2014

EP59-12317

Thread the 6 mm tube through the housing and set the housing down onto the
sound  insulation  making  sure  that  the  rubber  sleeve  on  the  pump  wires  is
under the cut away .

Replace 4 off 3mm x 16 Pozi screws holding the pump housing to the base
Refit the cable clamp to the top of the pump hosing but do not tighten the nut
yet

Reconnect  the  12  way  connector  from  the  front  part  of  the  base  unit  to  the
Power PCB

Reconnect the 2 way connectors to the pump and valve to the Power PCB

Reconnect the 6 mm tube to the pressure relief valve

Reconnect the 4 mm tube to the pressure relief valve.

Reconnect the 4 mm tube from the umbilical to the air filter assembly.

Make sure that all tools etc have been removed from the front and rear parts
of the unit.

Connect the 12 volt PSU to the socket on the rear unit.

Switch the power on by pressing the on/off button on the front panel

Briefly press the button at the bottom of the handset cradle.

The pump should start

Adjust the 6 mm tube in the top of the pump housing until the noise from the
pump is minimal and tighten the nut on the cable clamp using Torque Spanner
TD699 to 1.5 Nm.  The nut will normally be in contact with the main body.

Connect the test gauge on the calibration unit to the system by removing the
long 4 mm tube from the air filter and reconnecting via the test gauge.

«
...
29
30
31
32
33
...
»

Содержание IntelliPuff




















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPuff

Бренд: TaiDoc Страницы: 31

Бренд: Bacharach Страницы: 19

Бренд: Facom Страницы: 42

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: ICM Controls Страницы: 8

Prestige Series

Бренд: Ibanez Страницы: 54

Бренд: +GF+ Страницы: 64

Бренд: +GF+ Страницы: 12

Бренд: +GF+ Страницы: 48

Бренд: X-laser Страницы: 17

CoolPoint CP12-V8

Бренд: UFM Страницы: 14

Nitro-Save NS16

Бренд: TDI Страницы: 4

Бренд: RIDGID Страницы: 18

Бренд: BD Sensors Страницы: 4

Бренд: Roland Страницы: 2

Бренд: Karman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды