Keeler IntelliPuff Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 51

background image

Intellipuff Service Manual

Page 43 of 51

Issue D 27/02/2014

EP59-12317

PRINT:

this button has two functions:

1. Pressing it once forces the unit to automatically print,

providing a valid reading is available to print, else ‘0’ is
displayed. In this printing mode the printer does not have
to be switched on through the scroll menu system.

2. Scrolling menu: Pressing this button for 3 seconds allows

the user to enter into a menu system. Through this menu
system, and pressing the OD/OS button, the following
operation modes could be toggled.

a. PRNT: Switches the Printer ON/OFF. When the

Printer  is  on  through  this  menu  system,  the  green
LED  on  top  of  the  printer  paper  feed  comes  ON.
This  allows  the  unit  to  print  when  the  hand  unit  is
replaced  into  its  cradle  provided  a  valid  reading  is
stored  in  the  unit’s  memory.  i.e.  Prior  to  pressing
Demo  button  after  a  valid  reading.  As  explained
above, the printer does not have to be switched on
in  this  way  to  be  able  to  print  a  valid  reading  by
pressing  the  PRINT  button,  Pressing  the  print
button  will  print  a  valid  reading  regardless  of  this
setting.

i. ON

ii. OFF (Default setting – this is set during

calibration)

b. BUZZ: Switched the Buzzer to ON/OFF

i. ON (Default setting – this is set during

calibration)

ii. OFF

c. MODE : Switches the unit between AUTO and

CLINICAL modes of Operation.

i. AUTO (Default setting – this is set during

calibration)

ii. CLIN

d. IOP: Selects the display format to 0 or 1 decimal

places.

i. XX (Default setting – this is set during

calibration)

ii. XX.X

e. SELF TEST – Pressing the demo (D) button while

this  option  flashes  on  the  display  triggers  the
instrument  to  carry  out  self  test  after  a  series  of
puffs,  it  prints  the  status  of  LED,  Reservoir
Pressure,  Pressure  variation  in  percentage  for  soft
and hard puffs plus date of last calibration is printed
regardless of the printer being set to ON or OFF.

«
...
41
42
43
44
45
...
»

Содержание IntelliPuff




















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPuff

Бренд: PAT Страницы: 55

Бренд: PAT Страницы: 31

Бренд: OfiTE Страницы: 24

Бренд: Veeder-Root Страницы: 59

Smart Probes 115i

Бренд: TESTO Страницы: 17

Бренд: CAS Corporation Страницы: 20

Бренд: Fora Страницы: 64

Бренд: MRC Страницы: 14

Бренд: Tonghui Страницы: 65

Бренд: SEAWARD Electronic Страницы: 57

Бренд: az-instrument Страницы: 12

Бренд: Gatekeeper Страницы: 2

Бренд: Midtronics Страницы: 58

Бренд: Badger Meter Страницы: 32

Бренд: Frama Страницы: 2

Бренд: Leviton Страницы: 2

MoistureMaster Compact Plus

Бренд: LaserLiner Страницы: 80

Бренд: SIGRIST Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды