Keeler IntelliPuff Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 51

background image

Intellipuff Service Manual

Page 32 of 51

Issue D 27/02/2014

EP59-12317

Replacing the Main PCB

To remove the PCB

Disconnect 12 way connector from the Power PCB on the rear part of the unit

Disconnect 4 mm tube from the umbilical to the air filter

Disconnect 2 off 12 way connectors on the main board

Disconnect 2 way connector to handset cradle microswitch

Remove 4 x M3 x 16 screws and associated red spacers from the main PCB

Carefully  lift  the  blue  part  of  the  printer  ribbon  cable  connector  by  about
1.5 mm.    This  will  allow  the  printer  ribbon  cable  to  pull  easily  out  of  the
connector.

If  unit  is  using  2414-P-5018  PCB  pre  issue  E  then  there  will  not  be  EP39-
55305  (Pulsair  Button  Adaptor)  installed  between  the  PCB  and  Front  unit.
EP39-55305  will  need  to  be  ordered to accompany  2414-P-5018  if  replacing
the PCB.

Disconnect 2 off 2 way connectors on the underside of the PCB

To replace the PCB

Offer  PCB  to  the  main  unit  and  fit  2  off  2  way  connectors.    LED  09  is  the
printer LED and LED 10 is the on/off button LED

Push EP39-55305 (Pulsair Button Adaptor) into back of on/off switch prior to
pushing the PCB into position

Make  sure  the  blue  locking  section  of  the  printer  ribbon  cable  connector  is
lifted and offer the PCB into place ensuring that the printer ribbon cable slots
into the connector on the PCB.  Do not push the blue section home yet.

Fit 4 off M3 x 16 Pozi screws with their red spacers – bottom 2 first – and do
not over tighten.

Check  that  the  printer  ribbon  cable  is  fully  home  then  push  home  the  blue
locking section.

Reconnect 2 off 12 way connectors from the umbilical and rear part of the unit
correctly noting the names on the PCB

Refit 2 way connector from the handset cradle to the PCB

Reconnect the 4 mm tube and 12 way connector to the rear part of the unit.

«
...
30
31
32
33
34
...
»

Содержание IntelliPuff




















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPuff

Бренд: Yamaha Страницы: 83

Бренд: Yamaha Страницы: 63

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: OHAUS Страницы: 2

Бренд: LumaSense Страницы: 23

Бренд: Primes Страницы: 56

Бренд: Tektronix Страницы: 20

Бренд: Fluke Страницы: 22

Бренд: wtw Страницы: 52

Pianovelle GRP3

Бренд: Baldwin Страницы: 34

Бренд: Vega Страницы: 24

Бренд: Teledyne Analytical Instruments Страницы: 44

Бренд: Extech Instruments Страницы: 45

Бренд: Kreg Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды