Keeler IntelliPuff Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 51

background image

Intellipuff Service Manual

Page 39 of 51

Issue D 27/02/2014

EP59-12317

Fit the top case half assembly and ensure that it comes together all round
without strain.

Refit 5 off M2 x 12 cap head screws

Refit the browrest retainer under the browrest.

Carefully  clean  off  the  double  sided  adhesive  tape  used  to  retain  the  white
shroud from both case halves.

Apply fresh double sided adhesive tape as shown.

Refit  the  white  shroud  ensuring  that  it  fits  within  the  boundaries  of  the  case
half

Ensure that the browrest is open.

Refit  the  target  LED  cover  ensuring  that  is  under  the  browrest  and  that  the
target LEDs are not damaged.  The lugs on the cover will drop into the slots
on the white shroud and it can then be slid home ensuring that the ears are
squeezed against the shroud to allow the lugs to slide fully home.

Replace the M3 x 10 Pozi screw under the browrest.

M3 Nut

Browrest
Retainer

«
...
37
38
39
40
41
...
»

Содержание IntelliPuff




















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPuff

Бренд: ECC X-RAY Страницы: 14

Бренд: Calsense Страницы: 4

Бренд: Unico Страницы: 10

Бренд: OHAUS Страницы: 19

Бренд: OHAUS Страницы: 54

Бренд: Zenner Страницы: 2

Бренд: Rabid Elephant Страницы: 18

Бренд: Kawai Страницы: 72

Бренд: Kingfisher Страницы: 52

Бренд: PANCONTROL Страницы: 157

Бренд: D-tect Systems Страницы: 28

Бренд: VECTECH Страницы: 10

Бренд: DAPAudio Страницы: 8

Celviano AP-500

Бренд: Casio Страницы: 2

Бренд: Niigata seiki Страницы: 2

Бренд: Campbell Страницы: 42

Бренд: Purafil Страницы: 2

Бренд: LI-COR Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды