Keeler IntelliPuff Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 51

background image

Intellipuff Service Manual

Page 30 of 51

Issue D 27/02/2014

EP59-12317

Replacing the Pump Assembly

Please refer to the troubleshooting section before changing the pump
assembly.

To Remove the Pump Assembly

Open the main unit (see

Disconnect  the  12  way  connector  on  the  Power  PCB  to  allow  the  2  parts  to
separate.

Disconnect 2 off 2 way connectors to the Pump and Valve coil from the Power
PCB

Disconnect the 4 mm tube to the umbilical from the air filter assembly

Disconnect  the  4  mm  air  tube  from  the  pressure  relief  valve  on  top  of  the
pump housing by pushing the ring on the connector against the connector and
gently pulling the tube out.

Disconnect  the  6  mm  air  tube  form  the  pressure  relief  valve  as  described
above.

Unscrew  the  cable  clamp  on  top of  the  pump  housing  to  allow  the  6  mm air
tube to move down through it.

Remove 4 off M3 x 16 Pozi screws holding the pump housing to the base unit

Lift  the pump  housing  off of  the  pump  by  easing  the  6  mm  tube  through  the
cable clamp.

It  should  now  be  possible  to  unstick  2  layers  of  sound  insulation  under  the
pump from the base unit.

Remove the pump assembly.

To Replace the Pump Assembly

Carefully remove the protective sheet from the sound insulation.

Carefully place the Pump Assembly onto the base unit so that the silencer is
to the left of the pump motor and the slots in the sound insulation are in line
with the threaded inserts in the base unit.

Remove the cable clamp on top of the pump housing.

«
...
28
29
30
31
32
...
»

Содержание IntelliPuff




















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPuff

Бренд: Parker Research Corp Страницы: 3

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Xsens Страницы: 4

Бренд: Eastron Страницы: 2

Бренд: EASTERN INSTRUMENTS Страницы: 3

Бренд: TA Instruments Страницы: 7

Prestige Series

Бренд: Ibanez Страницы: 54

Бренд: Shimpo Страницы: 68

Бренд: janitza Страницы: 85

Бренд: Lambda Страницы: 35

Бренд: S&T Страницы: 23

Бренд: Hammerhead Страницы: 44

Бренд: Cressi Страницы: 36

Бренд: GW Instek Страницы: 91

EnviroAlert EA200

Бренд: Winland Страницы: 3

Бренд: Tohnichi Страницы: 12

ColorTrack Genesis

Бренд: Fresh Roast Systems Страницы: 9

Бренд: bihl+Wiedemann Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды