Kantronics MT1200 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 157

Kantronics MT1200 Скачать руководство пользователя страница 112

MCOM {ON | OFF}

default OFF

Supervisory (control) packets are not monitored unless MCOM is set ON and MON is
ON. In addition if your station is connected, control packets are not monitored unless
MCON is also ON. Control packets, when displayed, are distinguished from information
packets by the “<>” and “<<>>” character sets appended to the packet header. With
these characters, a letter is included to denote the type of control packet received, e.g.
<<c>> - a connect request packet. The types of control packets are listed below.

<C> Connect

request

<D>

Disconnect request

<DM> Disconnected

Mode

<UA>

Unnumbered Acknowledge

In addition, the following bracketed information will be added to the Information packets
as appropriate:

<UI> Unconnected

Information

frame

<Is>

Information frame (connected);

s = send sequence number

See also: AX25L2V2, MONITOR, MRESP

For details on control packets, see the book

AX.25 Amateur Packet-Radio Link-Layer

Protocol Version 2.0 October 1984

, available from the ARRL.

MCON {ON | OFF}

default OFF

When OFF, and connected, the TNC will display only those packets addressed to you.

When OFF, and not connected, all eligible packets (as determined by other monitor
commands) will be displayed.

When ON, all eligible packets will be displayed, whether connected or unconnected.

See also: MONITOR

MHEADER {ON | OFF}

default ON

104

«
...
110
111
112
113
114
...
»

Содержание MT1200






























































































































































Отзывы:

Нет отзывов