KAESER M100 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 384

background image

7.4 Low-temperature operation (winter)

The machine's electrical equipment is designed for starting at ambient temperatures as low as

14°F.
➤ In temperatures below 32°F, use the following operating materials/components:

■ Winter-grade engine oil,
■ Low viscosity cooling oil for the compressor
■ Winter-grade diesel fuel
■ Stronger battery

Use air hoses that are as short as possible under extremely cold conditions.

Allow the engine to warm up:

1.

Problems with pneumatic control at low temperatures.

Damage to the machine may be caused by ice particles in the pneumatic control and feedback

systems.
➤ Let the machine warm up in IDLE to ensure trouble-free regulation.

2. Allow the machine to warm up in idle with open air outlet valves until an airend discharge tem‐

perature of 86°F is reached. The airend discharge temperature is shown at the remote ther‐

mometer contact on the instrument panel.

7.4.1 Starting assistance

If the machine's starter battery is discharged, it can be started with the battery of another vehicle or

engine-driven machine.

Material Jumper cables

Precondition The machine is disconnected from the towing vehicle and safely parked.

Fire and explosion hazard.

High currents can flow if the battery is short-circuited. A shorted battery can catch fire or ex‐

plode.

Battery casing may crack and allow acidic fluid to spray out.
➤ Observe the instructions provided with the battery jumper cables.
➤ Do not connect the battery jumper cables to the negative pole of the discharged battery

or to the bodywork of the machine.

➤ Work with caution.

7

Initial Start-up

7.4

Low-temperature operation (winter)

74

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

«
...
84
85
86
87
88
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M100

Бренд: KAESER Страницы: 136

Бренд: ZIPPER MASCHINEN Страницы: 45

Бренд: MasterCraft Страницы: 13

Бренд: HammerSmith Страницы: 20

Бренд: ARB Страницы: 6

Бренд: Hitachi Страницы: 110

Бренд: Hitachi Страницы: 126

Бренд: Hitachi Страницы: 144

BEBICON SRL-5.5MB5A

Бренд: Hitachi Страницы: 2

Бренд: Premier Страницы: 11

Бренд: XTline Страницы: 23

Бренд: LA Audio Страницы: 2

Бренд: North American Страницы: 9

Бренд: Boss Страницы: 52

Бренд: Danfoss Страницы: 40

Бренд: KAESER KOMPRESSOREN Страницы: 24

Бренд: SALKI Страницы: 26

Бренд: Parkside Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды