KAESER M100 Скачать руководство пользователя

Страница: 83 / 384

Fig. 30 Changing the towing eye (fixed height towbar, USA chassis version)

Self-locking hexagon nut

Hex-head screw

Shock absorber fixing eye

Hex-head screw

Protective sleeve

Towbar

Shock absorber

Mounting pin

Ball coupling

Towing eye

1. Push back the protective sleeve

2. Unscrew and remove the nuts

of both screw connections.

3. Use the mounting pin

to beat out the rear screw

. Do not remove the pin in order to retain

the centring of the shock absorber in the towbar tube.

4. Remove the front screw

5. Remove the ball coupling

or towing eye

from the towbar tube

6. Push the new ball coupling

or towing eye

onto the towbar

until the fixating holes

match.

7. Use the screw

at the rear fixating hole of the towing eye/ball coupling to beat out the mount‐

ing and pin and to thread the shock absorber.

8. Insert the screw

through the front fixating hole.

9. Thread self-locking nuts

on both screws and tighten with torque wrench (see chapter 2.4.4).

10. Draw the protective sleeve over the fixings.

Checking the overrun braking mechanism

➤ Push the towbar tube in and out by hand.

If resistance is felt, the shock absorber is properly connected.

Installation

6.4

Adjusting the chassis

No.: 9_6999 23 USE

Operator Manual Screw Compressor
M100

Option rd/ro/rs

Содержание M100

































































































































































































































































































































































































Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды

KAESER M100, Руководство оператора

Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды