KAESER M100 Скачать руководство пользователя страница 240

Страница: 240 / 384

2. Remove the battery (batteries) and store in a frost-free room.
3. Make sure batteries are fully charged.

12.1.2 Long-term decommissioning and storage

Decommissioning the machine for 5 months or longer.

Material Receptacle

Preserving oil
Preservative
Desiccant
Plastic sheeting
Moisture-resistant adhesive tape

➤ The following measures must be taken for long-term decommissioning and storage:

Long-term decommissioning and storage tasks

See

chapter

Confirmed?

➤ Check engine coolant.

10.3.1

➤ Drain the engine oil.

10.3.6

➤ Drain the oil from the oil separator tank and the oil cooler.

10.4.3

➤ Fill the separator tank and engine with preserving oil.

10.4.2
10.3.5

➤ Run the machine for about 10 minutes to coat all parts with a protec‐

tive oil film.

–

➤ Disconnect the battery, the minus terminal first and then the plus ter‐

minal, and store in a frost-free room.

–

➤ Check the battery fluid level.

10.6

➤ Check the battery charge monthly and recharge if necessary to pre‐

vent the battery fluid freezing.

–

➤ Clean the battery terminals and coat with acid-resistant grease.

–

➤ Close the compressed air outlet valves.

–

➤ Use plastic sheeting and moisture-resistant adhesive tape to seal off

the following openings:

■ Engine air inlet
■ Compressor air inlet
■ Exhaust silencer

–

➤ Clean the bodywork and treat with preservative.

–

➤ Hang a notice on the instrument panel to inform of the decommis‐

sioning measures taken.

–

Tab. 96 Long-term decommissioning and storage checklist

12 Decommissioning, Storage and Transport

12.1 De-commissioning

228

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

Содержание M100

































































































































































































































































































































































































Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды

KAESER M100, Руководство оператора

Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды