KAESER M100 Скачать руководство пользователя страница 56

Страница: 56 / 384

Fig. 6 Machine layout

Compressor air filter

Inlet valve

Airend

Oil separator tank

Oil separator cartridge

Compressed air distributor

Temperature gauge switch

Pressure relief valve

Pressure gauge

Drive engine

Oil return line

Combination valve (thermostatic valve)

Oil cooler

Oil filter

Proportional controller

Engine air filter

Venting valve

Fan

Minimum pressure/check valve

Control valve

Ambient air is cleaned as it is drawn in through the filter

The air is then compressed in the airend

The airend is driven by an internal combustion engine

Cooling oil is injected into the airend. It lubricates moving parts and forms a seal between the ro‐

tors themselves and between them and the airend casing. This direct cooling in the compression

chamber ensures a very low airend discharge temperature.
Cooling oil recovered from the compressed air in the oil separator tank

gives up its heat in the oil

cooler

. The oil then flows through the oil filter

and back to the point of injection. Pressure

within the machine keeps the oil circulating. A separate pump is not necessary. A thermostatic

valve

automatically maintains optimum cooling oil temperature.

Compressed air, freed of cooling oil in the oil separator tank

, flows through the minimum pres‐

sure / check valve

into the air distributor

. The minimum pressure / check valve ensures that

there is always a minimum internal pressure sufficient to maintain cooling oil circulation in the ma‐

chine.
The cooling fan

ensures optimum cooling of all components within the enclosure.

Design and Function

4.3

Machine function

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

Содержание M100

































































































































































































































































































































































































Результаты поиска

Содержание M100

Отзывы:

KAESER M100, Руководство оператора, Страница: 56 / 384

Результаты поиска

Содержание M100

Отзывы: