KAESER M100 Скачать руководство пользователя страница 134

Страница: 134 / 384

Fig. 56 Draining the engine oil (closed floor pan - stationary machine)

Screwed sealing cap, engine oil drain

Oil filler neck cover, engine oil

Engine oil sump

Shut-off valve (ball valve)

I - open

0 - closed

1. Open the right-hand access door.
2. Remove the oil filler cover.
3. Place the oil receptacle below the drain point.
4. Unscrew the filler plug

at the oil drain.

5. Open the shut-off valve

at the engine's oil pan and catch the engine oil.

6. Close the shut-off valve and replace the screwed sealing cap.
7. Replace the plug in the filler port.
8. Close the door.

Dispose of old oil and oil-soaked working materials according to environmental protection

regulations.

Further information See chapter 10.3.5 for engine oil filling.

Further information regarding changing the engine oil is provided in the engine manufacturer's op‐

erating manual.

10 Maintenance

10.3 Engine maintenance

122

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

Option oe, rw, rx

Содержание M100

































































































































































































































































































































































































Результаты поиска

Содержание M100

Отзывы:

KAESER M100, Руководство оператора, Страница: 134 / 384

Результаты поиска

Содержание M100

Отзывы: