KAESER M100 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 384

KAESER M100 Скачать руководство пользователя страница 132

3. Wait 5 minutes then check the oil level.

It takes a few minutes for oil to reach the sump.

Top up if the level is too low.

4. Replace the plug in the filler port.
5. Reconnect the negative battery terminal.
6. Close the access door.

Starting the machine and performing a test run:

1. Switch the machine on and run it in IDLE mode for approx. 5 minutes.
2. Shut down the machine.
3. Wait until the machine has automatically vented.

Pressure gauge reads 0 psig!

4. Open the right-hand access door.
5. Check the oil level after about 5 minutes.

Top up if the level is too low.

6. Visually inspect for leaks.
7. Close the access door.

10.3.6 Changing the engine oil

The engine oil should be changed:
■ according to the maintenance schedule,
■ according to the degree of contamination of the intake air,
■ at least once a year.

Check the operating manual of the motor manufacturer for information on oil change in very

dusty environments.

Material Engine oil

Oil receptacle
Wrench
Cleaning cloths

Precondition The machine is switched off.

The machine is standing level.
The machine is fully vented, the pressure gauge reads 0 psig.
Engine at operating temperature.
All compressed air consumers are disconnected and the air outlet valves are open.
The negative cable to the battery is disconnected.

Danger of burns from hot components and escaping engine oil!
➤ Wear long-sleeved clothing and protective gloves.

10 Maintenance

10.3 Engine maintenance

120

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

«
...
130
131
132
133
134
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов